The Toro TFS series flow sensors provide reliable flow information to aid in the detection of and response to system issues like piping breaks, while being accurate enough for tracking water usage.
Socket end tee
Compatible with competitor controllers
Reliability, durable, impeller-based sensor provides accurate flow information
Removable sensor design for easy replacement without removal of tee
± 1.5 % linearity/repeatability
Sensor pre-installed in tee
Baseline’s biCoders work with Baseline’s biLine two-wire technology to create the only true bi-directional two-wire devices in the industry. Baseline’s biCoders not only receive commands from the controller, they also send real-time information back to the controller. Plus, Baseline’s biCoders have built-in diagnostic LED lights that tell you at a glance whether the device is working. This smart technology also enables you to assign any biCoder to a zone or function from the controller after the biCoder has been installed in the field. With a multi-station biCoder, you can assign any station to any zone, in any order.
Multi-station bi-coders have color coded wires for each station
Manufactured with 24 inch of 16 ga PVC jacketed solid core wire to connect to the two-wire and 24 inch of 18 ga PVC jacketed stranded core wire to connect to the valve wire
Run up to two typical solenoids up to 150 ft away from valve decoder using standard 14 ga irrigation wire per station wire (excluding BL-5201)
All bi-coders are fully sealed, submersion-proof, and approved for direct bury
All bi-coders have built-in LEDs that blink during communications on the two-wire side and remain lit when power is supplied to the valve
Automatically shut down any attached solenoids if communication is lost with the controller
Freeze/heat resistant -4 to 140 degrees F
Built-in surge protection
Shock resistant
Pause bicoders are able to interface and read any normally closed switch pause device (including rain, wind, pressure, tank floats, and temperature)
Includes a built-in amperage meter that accurately measures and diagnoses valve solenoid electrical problems such as: “no current,” “station short,” or “over current”
For simple, water saving, weather-adjusting, automatic irrigation control, look to the Irritrol Climate Logic weather system. The three-component kit consists of a wireless weather sensor to transmit data from the outdoors, a receiver module to attach at the controller, and an SD card loaded with 40 years of historical weather information (specific to geographic location).
Built in radios
Temperature sensor for monitoring air temp
Solar sensor
Receiver module
Rain and freeze sensor
Baseline’s biCoders work with Baseline’s biLine two-wire technology to create the only true bi-directional two-wire devices in the industry. Baseline’s biCoders not only receive commands from the controller, they also send real-time information back to the controller. Plus, Baseline’s biCoders have built-in diagnostic LED lights that tell you at a glance whether the device is working. This smart technology also enables you to assign any biCoder to a zone or function from the controller after the biCoder has been installed in the field. With a multi-station biCoder, you can assign any sta??on to any zone, in any order.
Multi-station bi-coders have color coded wires for each station
All bi-coders are fully sealed, submersion-proof, and approved for direct bury
Run up to two typical solenoids up to 150 ft away from valve decoder using standard 14 ga irrigation wire per station wire (excluding BL-5201)
Shock resistant
All bi-coders have built-in LEDs that blink during communications on the two-wire side and remain lit when power is supplied to the valve
Manufactured with 24 inch of 16 ga PVC jacketed solid core wire to connect to the two-wire and 24 inch of 18 ga PVC jacketed stranded core wire to connect to the valve wire
Freeze/heat resistant -4 to 140 degrees F
Automatically shut down any attached solenoids if communication is lost with the controller
Built-in surge protection
Includes a built-in amperage meter that accurately measures and diagnoses valve solenoid electrical problems such as: “no current,” “station short,” or “over current”
Pause bicoders are able to interface and read any normally closed switch pause device (including rain, wind, pressure, tank floats, and temperature)
Baseline’s biCoders work with Baseline’s biLine two-wire technology to create the only true bi-directional two-wire devices in the industry. Baseline’s biCoders not only receive commands from the controller, they also send real-time information back to the controller. Plus, Baseline’s biCoders have built-in diagnostic LED lights that tell you at a glance whether the device is working. This smart technology also enables you to assign any biCoder to a zone or function from the controller after the biCoder has been installed in the field. With a multi-station biCoder, you can assign any sta??on to any zone, in any order.
All bi-coders are fully sealed, submersion-proof, and approved for direct bury
Multi-station bi-coders have color coded wires for each station
Includes a built-in amperage meter that accurately measures and diagnoses valve solenoid electrical problems such as: “no current,” “station short,” or “over current”
Manufactured with 24 inch of 16 ga PVC jacketed solid core wire to connect to the two-wire and 24 inch of 18 ga PVC jacketed stranded core wire to connect to the valve wire
Built-in surge protection
All bi-coders have built-in LEDs that blink during communications on the two-wire side and remain lit when power is supplied to the valve
Automatically shut down any attached solenoids if communication is lost with the controller
Run up to two typical solenoids up to 150 ft away from valve decoder using standard 14 ga irrigation wire per station wire (excluding BL-5201)
Pause bicoders are able to interface and read any normally closed switch pause device (including rain, wind, pressure, tank floats, and temperature)
Shock resistant
Freeze/heat resistant -4 to 140 degrees F
Surge protection (FSSURGEKIT) is recommended for most systems – One at the Flow Sensor, and if more than 50 ft. of wire run, one at the Pulse Transmitter. FSSURGEKIT is not required for Two-Wire Decoder Systems and not compatible with Wire Decoder Systems and not compatible with
For simple, water-saving, weather-following, automatic irrigation control, Irritrol® introduces the Climate Logic® Weather Sensing System. Consisting of three components–a wireless transmitting weather sensor for installation outdoors, a receiver module to attach to the Irritrol controller, and an SD card with the 10-year, local historical weather information–the system monitors weather data, transmits it to the module, then alters the controller’s program to “follow the weather”. As for compatibility, the Climate Logic Weather Sensing System works with the Rain Dial®-R, Total Control®-R, KwikDial® and the new MC-E controllers (blue model).
Built-in radios
For easy, wireless installation with less labor than wired systems
Weather SD card
Contains the 10-year, historical weather information for North America with location access by zip code or latitude/longitude
Solar sensor
Monitors the amount of the landscape site’s sun exposure
Temperature sensor for monitoring air temperature
Shuts system off in cold weather
Rainsensor
Adjustable for amount of precipitation to shut off system
Receiver Module
– Connects to the controller with a single plug-in cord. No bundle of wires to individually attach
Use the Hunter FCT Wired Receptacle Tee for superior irrigation. This receptacle tee is used to protect against flood damage and to protect against erosion. It has a single button, which enables individual systems to be programmed at a specific flow level. It is ideal to use in commercial piping systems and residential piping systems.
Automatically shuts down system if an overflow condition occurs
Schedule 40 wall thickness
Multi-color LED provides system status to display when power is applied and indicate if flow is within limits
Protects against flood damage and erosion
Calibration for exact system control, single button allows each system to be programmed at a specified flow level
Use the Hunter Rain Sensor for better irrigation in outdoor areas. This Rain-Clik sensor comes with an adjustable vent ring, which allows for reset delay. It has Quick Response technology, so the system will shut down in order to conserve water during rainy weather.
Quick response feature shuts the system off as soon as it starts raining
Adjustable vent ring allows for setting of reset delay
Polycarbonate housing
Maintenance-free design with 10-year battery life for wireless rain-clik
Wireless unit available with 800 ft range from wireless sensor to receiver
Compatible with most controllers
Taking water management to the next level, the proven Irritrol® RainSensor Series makes watering in the rain a mistake of the past. The reliable wireless and wired rain sensors conserve water by preventing irrigation during or after sufficient rainfall, while the wireless rain/freeze sensor also helps reduce vegetation damage and icing conditions when the temperature drops below a predetermined set point. With its compact design and host of convenient features, the RainSensor Series is the perfect complement to any standard controller.